国产高清女同学巨大乳在线观看 ,日本乱人伦aⅴ精品,亚洲欧美综合在线天堂,18禁黄久久久AAA片

歡迎光臨山東墨源數控設備有限公司官網為您提供:保麗龍雕刻機,五軸保麗龍刻機,四軸保麗龍雕刻機
收藏本站在線留言進入手機站

NEWSCENTER
新聞資訊
聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

新聞資訊 當前位置：首頁 - 新聞中心 > 新聞資訊

使用五軸泡沫雕刻機時維修保養和注意事項

來源：http://m.xacfgd.com.cn 時間：2020-10-15 

1.發動前查驗五軸雕刻機各處搖桿是不是在正常部位，各運動部件是否完好無損，滑軌有機油潤化，隨后發動底速動轉1~2分鐘，觀查是不是有異?，F象，等數控車床運轉正常后方能進行作業。
1. Before starting, first check whether the rocker of the five axis engraving machine is in the normal position, whether the moving parts are intact, and whether the slide rail is lubricated with oil. Then, start the machine at the bottom speed for 1-2 minutes to observe whether there is any abnormal phenomenon. The operation can be carried out after the CNC lathe runs normally.
2.泡沫雕刻機主軸軸承、操作臺和滑軌面制止敲擊和沖擊，操作臺及鋼軌面不可亂堆專用工具和毛胚及不相關的鋼件或物件。
2. the main bearings, operation tables and slide surfaces of foam engraving machines should be used to stop percussion and impact. Special tools and hairs and unrelated steel parts or objects should not be huddle on the operation platform and rail surface.
3.有效切削，調節適合的變大（變小）倍率，視出產加工情況選擇數控刀片、轉速比、下刀量、出產加工速率及順，逆銑方位。
3. Effective cutting, adjust the suitable increasing (decreasing) ratio, and select CNC blade, speed ratio, cutting amount, production processing rate and the direction of forward and backward milling according to the production and processing conditions.
4.悉數出產過程中，不能戴手套，關于出產過程中有木渣飛濺時要做好雙眼的保護作業，出產過程中不可以用力或碎布條等臟物觸碰現已旋轉的數控刀片，在鏟除木渣時要確保數控刀片完全終止運轉才可以木渣。
4. Do not wear gloves in the production process. When there is wood residue splashing in the production process, protect your eyes. Do not use force or rags to touch the rotary NC blade. When removing the wood residue, ensure that the NC blade completely stops running to eliminate the wood residue.
5.作業完畢，斷電，鏟除各方位木渣，臟物。其他相關輔助工具必須放還原處。
5. After operation, cut off the power and remove the wood slag and dirt in all directions. Other related auxiliary tools must be placed in the restoration place.
6.作業臺面及滑軌每日擦洗干凈，不能有木渣、油漬殘渣等。
6. The worktable and slide rail shall be cleaned daily, and there shall be no wood residue, oil residue, etc.
7.接連運作時間每天10鐘頭以下，確保冷卻循環水的清理及離心水泵的正常作業，決不能夠 使水冷散熱伺服電機出現少水情況，定時執行拆換冷卻循環水，以避免溫度過高。儲水箱里邊的冷卻循環水每日必須拆換一次；
五軸保麗龍雕刻機
7. The continuous operation time is less than 10 hours per day, to ensure the cleaning of cooling circulating water and the normal operation of centrifugal pump, and never make the water cooling servo motor lack of water. Regularly replace the cooling circulating water to avoid excessive temperature. The cooling circulating water inside the water storage tank must be removed and replaced once a day;
8.五軸泡沫雕刻機每一次設備運用完畢，要留心鏟除，盡量將服務平臺及傳動裝置上的煙塵鏟除干凈，準時（每星期）對傳動裝置（X,Y,Z三軸）潤化加油。滑軌可運用油槍上油，滾珠絲桿要加0﹟潤滑油脂或無鹽黃油；
8. the five axis foam engraving machine should be carefully removed after every equipment is used. Try to clean up the smoke and dust on the service platform and the transmission device, and run the oil on the X (Y, Z three axis) on time (every week). The slide rail can be oiled with oil gun, and the ball screw should be added with 0 lubricating grease or salt free grease;
9.設備若長時間不運用，應準時（每星期）加油空走，以確保傳動裝置的和諧能力。
9. If the equipment is not used for a long time, it should be filled with oil and left empty on time (every week) to ensure the harmonious ability of the transmission device.
10.準時（依運用情況）鏟除電器箱里塵土，查驗接線端子排螺釘是不是松脫，以確保設備電源電路性，靠譜運用；
10. Remove the dust in the electrical box on time (according to the application situation), and check whether the screw of the terminal block is loose, so as to ensure the safety of the power supply circuit of the equipment and reliable application;
11.準時（依運用情況）查驗設備各構件螺絲是不是松脫，以確保設備靠譜運轉。
11. Check whether the screw of each component of the equipment is loose or not on time (according to the application situation) to ensure the reliable operation of the equipment.
12.對電器進行保護保養查驗時，一定要斷開開關電源，待監控器無顯示信息及主操控回路指示燈吹滅后，即可進行。
12. When checking the protection and maintenance of electrical appliances, it is necessary to disconnect the switching power supply. After the monitor has no display information and the indicator light of the main control circuit blows out, it can be carried out.